We offer three shipping methods: 1) Free Standard Shipping - takes 7-20 working days (except remote areas) and requires a remote fee for those areas. 2) Expedited Shipping - takes 4-10 working days and requires an additional fee. Contact us if you want to use express shipping. 3) Ocean Shipping (for USA only) - takes 18-35 working days. Contact us if you want to use sea shipping.
Introducing the Happymodel Bassline 2s FPV Racer, designed in collaboration with team pilot Nathan Loopz and now available after being conceptualized in 2019.
Experience ultimate control and performance with the X12 5-in-1 AIO flight controller featuring built-in 2.4G ELRS V2.0 and OPENVTX. Long-range transmission is made possible with the high-power 400mw VTX, and the drone can be upgraded to support ELRS V3.0 firmware.
Powered by EX1103 KV11000 motors, the Bassline 2s delivers high speed and power. Capture stunning aerial footage with the CaddxFPV Ant FPV camera, and enjoy extended flight time with 2S batteries ranging from 350mah to 650mah (not included). The large battery tray accommodates batteries up to 17mm wide and 13mm in height.
X12 5-in-1 AIO flight controller with built-in 2.4G ELRS V2.0 and OPENVTX for ultimate control and performance
High-power 400mw VTX for long-range transmission
Upgradeable to support ELRS V3.0 firmware
Equipped with powerful EX1103 KV11000 motors for high speed and power
Features a CaddxFPV Ant FPV camera for stunning aerial footage
Compatible with 2S batteries in the range of 350mah/450mah/550mah/650mah (batteries not included)
Large battery tray can accommodate batteries up to 17mm wide and 13mm height for extended flight time.
Onboard 4in1 ESC Power supply: 1-2S LiPo/LiPo HV Current: 12A continuous peak 15A (3 seconds) Support BLHeliSuite programmable Default Factory firmware: Z_H_30_REV16_7.HEX Default protocol: DSHOT300 Support Bluejay firmware
Onboard SPI ExpressLRS 2.4GHz Receiver Packet Rate option: 50Hz/150Hz/250Hz/500Hz ExpressLRS Firmware version: V2.0 RF Frequency: 2.4GHz Antenna : SMD antenna Telemetry output Power: <12dBm Receiver protocol: SPI ExpressLRS Compatible with ExpressLRS V2.0 TX Module Couldn’t flash separately ExpressLRS firmware Could flash FC firmware to support ExpressLRS v3.0 TX module
Onboard SPI Frsky D8/D16 receiver Versio SPI BUS receiver Frsky D8/D16 compatible Compatible Non EU transmitter D8/D16 model Channels: 8ch/16ch No ground interference ( Transmitter and receiver 1 m from the ground): 200meter Failsafe support
Onboard SPI Flysky receiver Version SPI BUS receiver Protocol: AFHDS-2A Channels: 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 200meter Failsafe support
PNP Version(without onboard receiver) Full UART1 for external Receiver Support CRSF/GHOST/SBUS/IBUS/DSMX protocol IR1 pad(invert RX1) used for SBUS input
Onboard 5.8g OPENVTX Firmware version: OPENVTX Smartaudio v2.1 PIT Mode support RCE Mode support Channels:48ch Transmitting Power: 0/RCE/25mw/100mw/400mw Power supply: DC 5V Current (5v): <650ma (400mw)
Caddx ANT 1200tvl camera Image Sensor: 1/3" CMOS Sensor Horizontal Resolution: 1200 TVL TV System: NTSC or PAL IMAGE: 16:9 or 4:3 Synchronization: Internal Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000 S/N Ratio : >52dB (AGC OFF) Video Output: CVBS Lens: 1.8mm Min. Illumination: 0.001Lux@F1.2 Auto Gain Control: YES WDR: Global WDR DNR: 3D DNR Dimensions: 14*14mm(with bracket to 19*19mm) Wide Power Input: DC 3.7-18V Weight: 2g (N.W.)