Skip to content
Free shipping to most of countries
Free shipping to most of countries

Happymodel Mobeetle6 65mm Whoop and Toothpick 2-IN-1 FPV Racer Drone W/DiamondF4 Flight Controller and 0702 KV23000 Motors

Save 23% Save 23%
Original price $167.99
Original price $167.99 - Original price $167.99
Original price $167.99
Current price $129.00
$129.00 - $129.00
Current price $129.00
SKU 6960689
Receiver: ELRS


The new Mobeetle6 BNF would be the lightest 65mm mass production whoop in the world, hope you will enjoy it . The DiamondF4 Flight controller and 0702 motors were inspired from Angry Don FPV, we really appreciated for his help to Happymodel and to this hobby. We also very expecting to the performance of this BNF with the new Diamond F4 ELRS flight controller.





The new Happymodel Mobeetle6 BNF would be the lightest 65mm mass production whoop in the world, hope you will enjoy it .

The DiamondF4 Flight controller and 0702 motors.

Features:
The lightest 1S Whoop and Toothpick 2-IN-1 fpv drone
Comes with tooth pick frame for convert
Powerful and efficiency
The lightest 1s AIO 5IN1 F4 flight controller
New Unibell SE0702 brushless motors with pcb wire board
Built-in OPENVTX up to 400mw
Low profile Canopy design

Specifications:
Brand Name: Happymodel
Item Name: Mobeetle6 whoop and toothpick 2-IN-1 FPV Racer Drone
Wheelbase: 65mm
Size: 80mm*80mm*30mm
Weight: 17.5g (without battery)

Motor
Mode:SE0702 KV23000
Configu-ration:9N12P
Stator Diamter:7mm
Stator Length:2mm
Shaft Diameter:Φ1mm
Motor Dimension(Dia.*Len):Φ9.5mm*14mm
Weight(g):1.5g
No.of Cells(Lipo):1S only

Propeller
Weight:0.19g
Material:PC
Pitch:1 inchProps Dia:30mm
Center Hole Dia:1mm

Flight controller
(ELRS SPI RX version)DiamondF4 ELRS FC Firmware target: CrazybeeF4SX1280
(Frsky SPI RX version) DiamondF4 FR FC Firmware target: CrazybeeF4FR
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000 or ICM20689 or BMI270(SPI connection)
Original whoop size compatible
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G OPEN VTX
Built-in SPI ELRS V2.0/Frsky receiver
Built-in 5V 1A BEC

Onboard 4in1 ESC
MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_50_REV16_8.HEX
Default protocol: DSHOT600

Onboard SPI ExpressLRS 2.4GHz Receiver
Packet Rate option: 50Hz/150Hz/250Hz/500Hz

ExpressLRS Firmware version: V2.0
RF Frequency: 2.4GHz
Antenna : Enameled copper wire antenna
Telemetry output Power: <12dBm
Receiver protocol:  SPI ExpressLRS
Compatible with ExpressLRS V2.0 TX Module

Onboard Frsky SPI D8 receiver Version
SPI BUS receiver Frsky D8 compatible

Compatible Non EU transmitter D8 modelChannels: 8ch
Failsafe support

Onboard 5.8g OPENVTX
Firmware version: OPENVTX

Smartaudio v2.1
PIT Mode support
RCE Mode support
Channels:48ch
Transmitting Power: 0/RCE/25mw/100mw/400mw
Power supply: DC 5V
Current (5v): <650ma (400mw)
No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m
Couldn’t flash separately ExpressLRS firmware

Runcam Nano3
Model: RunCam Nano 3
Image Sensor: 1/3″ CMOS
Horizontal Resolution: 800TVL
Lens : 2.3mm(M6.5) FOV 140°
Signal System: NTSC
S/N Ratio: >50dB
Electronic Shutter Speed: Auto
Auto Gain Control (AGC): Auto
Min. Illumination: 0.01Lux@1.2F
D-WDR: Auto
Day/Night: Color
Power:DC 3-5.5V
Current: 110mA@5V 120mA@3.3V
Housing Material: ABS
Net Weight: 1.2g
Dimensions: L14mm*W14mm*H9mm

Lipo Battery
Capacity:300mAh
Voltage:3.8v
Continuous Discharge Rate: 30C
Size: 57mmx12mmx7mm
Connector: PH2.0
Weight: 7.5g

Package Included:
1*65mm whoop Frame (Mobula6 frame)
1*65mm toothpick frame(Mobeetle6 frame)
Option1: DiamondF4 ELRS built-in SPI ELRS receiver
Option2: DiamondF4 FR built-in SPI FRSKY receiver
4*SE0702 KV23000 Unibell brushless motor
1*Gemfan 1210 31mm propeller(4cw+4ccw)
1*Runcam Nano3
1*Built-in 5.8G 48ch 25mw-400mw OPENVTX
2*1s 300mah Lipo battery(Need more batteries for Happymodel Mobeetle6? Click here)
1*Mobula6 canopy
1*Propeller disassemble tool
1*Screwdriver