Products

2PCS Makerfire Micro Whoop Frames Wheelbase 65mm with Whoop Canopies for 716 Motors Specifications:Name: Whoop Frame,Whoop Canopy Frame Wheelbase:65mmApply for: 716 Brushed MotorsWeight: 3.72gApplies for: Makerfire Armor 65 Lite, Armor 65 Plus, Armor 65 Pro, Tiny 6X and etc.Package included: 1x White 65mm Whoop Frames...

2PCS Makerfire Whoop Frames Wheelbase 75mm with Micro Whoop Canopies for 8020 Motors Specifications:Name: Whoop Frame,Whoop Canopy Frame Wheelbase: 75mmApply for: 8020 Brushed MotorsWeight: 6.01gPackage included: 1x White 75mm Whoop Frames 1x Blue 75mm Whoop Frames 1x White Whoop Canopy 1x Blue Whoop Canopy1x...

AOkoda CX405 1S LiPo Battery USB Charger 4.2V 4.35V LiPo LiHV JST-PH 2.0 mCPX Connectors Tiny Whoop(Pack of 2)  Note:The appearance has changed, the function and performance have not changed Specifications:Support battery type: LiPo 3.7V / Li-Hv 3.8V for 1CellInput range: 5V plusmn;5%@0.5~2AOutput range: 2.50~4.35V...

The Caddx Polar Micro Air Unit is an advanced video transmission module that supports a 5.8 GHz digital video signal and 720p 120fps image transmission, with a transmission range of up to 4km and a minimum end-to-end latency within 28 ms. The air unit can be mounted...

CADDXFPV Walnut 4K/60fps Gyroflow IP64 Action Camera 60g with ND8 ND16 Filter Features:1. The highest 4K/60fps high-definition picture quality, the bit rate can reach 100mbps.2. The weight is only 63.4gOnly less than half the weight of a gopro.3. Magnetic charginga. Compared with most action cameras, many...

Carbon fiber chassis kit upgrade of WLToys 104001 Thickness：2mm  Weight: 81g Note：Please check the picture (2mm kit /5mm kit) before you order.  2mm kit 8pcs , 5mm kit only 5 pcs! A. 2 mm thickness  chassis weight 81g. Total 8pcs (1set) B. 5 mm thickness ...

DarwinFPV TinyAPE Freestyle 2.5" 2-3S FPV Racing RC Drone with RunCam Nano4 Thumb Camera Support ELRS Tiny Ape Freestyle is the first 2.5'' drone for Darwinfpv.It comes with the Darwin ELRS2.0 F411 15A Bluejay AIO and the VTX006 which has 25-600mW output power. Specification:Weight: 50.3g (without...

DJI FPV Air Unit with Camera The FPV Air Unit features an ultra-low-latency high-definition digital image transmission, 1080p/60fps video recording, and eight frequency channels, allowing eight pilots to fly simultaneously. Digital HD systems have traditionally been rather bulky and unwieldy to mount on a...

DJI FPV Goggles V2 Features: High definition, Low latency, Strong sense of immersion, Long image transmission distance, The package contains flying glasses batteries, fully charged can be used for about 110 minutes. Specification:Flying glasses:Weight: about 420 grams (including headband and antenna)Dimensions:184 x 122 x 110 mm...

DJI Naza-M V2 (Includes GPS) The Naza-M V2 is a powerful flight controller for enthusiasts, as well as commercial and industrial flyers. It is easy to install, simple to configure, and extremely stable. Overview:All-In-One Compact Multi-Rotor Autopilot SystemSupports 9 Different of Multi-Rotor Configurations, Ideal...

Introducing Dogcom's 1S battery meant for whoop drones. Dogcom LIPO's are high quality and stable. This is the pack you want to fly when you only settle for the best! Features: High & stable quality. Higher energy density. Lower internal resistance. Longer life cycle....

EMAX Tinyhawk 3 FPV Racing Drone BNF and RTF   Self-improvement is a core trait for the engineers at EMAX, which is why when approached about a new successor to the Tinyhawk series, they designed the Tinyhawk III to build upon all the strengths...

Important Note:  F1 Pro Flyball Soccer Drone now has an upgraded version: GT2 Soccer Drone(Click to buy). If you order F1 Pro, we will automatically ship you the upgraded GT2 Soccer Drone F1 Pro Competition FLYBALL Soccer Drone - Ideal for competitive play, training,...

Fly Wing H1-Heli Helicopter Flight Controller 3D Flybarless Gyro System FlyWing H1-HELI GPS-Mount:https://www.thingiverse.com/thing:5416224(Thank you so much for Mr. Katsunori who designed and shared to us) Specification:Material: MetalTechnical parameters: Value 2Wheelbase: Bottom PlateSize: 37x28x20mmModel Number: H1For Vehicle Type: HelicoptersTool Supplies: ToolsFour-wheel Drive Attributes: BatteryUpgrade Parts/Accessories:GPSWheelbase:ScrewsRC Parts & Accs:flight...

Flysky FS-I6S RC Transmitter Tx 2.4G 10CH with IA6B Receiver/without IA6B Receiver Features:Flysky FS-i6S remote controller is equipped with 10CH 2.4G touch screen, can be used for RC airplane, multicopter.Support combining 2 switches as 1 channel, and channels can be user-defined.Match with both FS-iA6B (6channel)...

The FMS 1/24 Bigfoot model-Max SMASHER adopts the FCX24 chassis. The car body design restores the appearance of a first-generation American pickup truck. The huge hollow tires provide excellent shock absorption. The two-speed gearbox, controlled by the third channel, can not only provide strong...

FCX24 meticulously designed by FMS team will redefine the small scale climbing rc car. As the first product of the FCX24 series, the car body is the POWER WAGON in 1949, which appeared in the form of a mud off-road truck. It is positioned...

FrSky ACCST Taranis Q X7 2.4GHz 16CH Transmitter With RX8R/XMPF3E/XSRF3E Features:Quad Ball Bearing GimbalsReceiver MatchAudio Speech Outputs (values, alarms, settings, etc.)Antenna Status Detection and adjustmentReal-time Flight Data LoggingReceiver Signal Strength Indicator (RSSI) AlertsSuper Low LatencySmart Port SupportedVibration AlertsModel configuration files compatible with TARANIS X9D...

GAONENG GNB27 Connectors Set Male Female 1.0 Banana Connector for GNB27 Connector FPV 1S Whoop Drone Note:The male and female connectors are subject to the picture,Please check clear, The terminal molded case identifies the positive and negative poles, and must be welded according to...

Gemfan Halloween 51466 V2 Three Blade Propeller(Pack of 12) Specifications:Inch:5.1"Pitch:3.6"Weight:3.79g/ per prop (No Battery)Material: PolycarbonateColor:Orange,Black（Total 3 patterns）Drone: FreestyleMounting:M5 Packge Including:6xCW Gemfan 51466 Propeller(Each pattern 2*CW)6xCCW Gemfan 51466 Propeller(Each pattern 2*CCW)

Gemfan Hurricane 51433 Propeller for FREESTYLE (Pack of 24pcs) Specifications:Blades:3Material:PCPitch: 3.5inchProp Disk Diameter: 129.7mmCenter Thickness: 6mmCenter Hole Inner diameter: 5mm Max Prop Width:14.3mmWeight: 3.8gAdaptive Motor:2206-2306Colors: Transparent, Clear black, Orange, Purple, Pink, Yellow Package included:4x Gemfan Hurricane 51433 Propeller -  Transparent4x Gemfan Hurricane 51433 Propeller -  Clear...

Gemfan Hurricane 51466 Propeller (Set of 8) Get ready to race with Gemfan's Hurricane 51466 Durable 3-Blade Propeller. The 51466 Hurricane series was designed for agile flight at high speed with its incredibly low weight at just over 4g.Compared to the 51499 Hurricane, the...

GNB 4pcs 650mAh 1S 3.8V HV LiPo Battery 60C with JST-PH 2.0 PowerWhoop mCPX Connector for Inductrix FPV Plus 75mm Frame Kit Micro FPV DroneDescription:Item: 650mAh HV 1S Lipo BatteryCapacity: 650mAhVoltage: 3.8VContinuous Discharge Rate: 60CCapacity: 650 mAhDimension: xx * xx * xx mmWeight: xxg/per...

GNB 550mAh 22.2V 80C 6S Lipo Battery with XT60 Plug for FPV Racing Drone RC Quadcopter, etcSpecifications:Capacity(mah): 550mAhCell(s): 6S1PDischarge Rate(C): 80CWeight(g): 103gSize(LWT)(mm): 61mm*31mm*31mmVoltage(v):22.2VPlug:  XT60Package include:1* GNB 550mAh 22.2V 80C 6S Lipo Battery

GNB/GAONENG 300mAh 1S 3.8V HV 60C battery with Head cover Molex 1.25 Connector(Pack of 6) SpecificationModel No.:GNB3001S60AHVCapacity:300mAhConfiguration:1S1PNominal Voltage:3.8VDimension:6.5*11.5*51mm Appr.Weight:10g (+/-1g)Max cont. discharge (C-rate/current):60CMolex1.25 Connector Package Included:6*GNB 300mAh 1S 3.8V 60C battery

GNB/GAONENG 350mAh HV 1S Lipo Battery 30C 3.8V JST-PH 2.0 Powerwhoop Connector(Pack of 6) Specifcation:Item:350mAh HV 1S Lipo BatteryRate: 30CDimension: 0.25*0.45*2.79 inch（L*W*H）Weight: 8.5g/per unitCapacity: 350mAh Package Included:6*350mAh HV 1S Lipo Battery  

GNB/GAONENG 600mah 3.8V 1S 90C Lipo Battery PH2.0 Connecter(Pack of 6) Specifications:Item: 6pcs GNB 600mah 3.8V 1S 90C Lipo Battery Rate: 90CVoltage:3.8VCapacity: 600mAhConnector: PH2.0 ConnectorWeight: 13.5g for eachSize: 61*18*7mm Package Included:6pcs GNB 600mah 3.8V 1S 90C Lipo Battery

Happymodel 1-2S Crux3 3 inch Brushless Toothpick Drone with Frsky SPI/Flysky SPI/DSM2/X SPI/RXSR/TBS Receiver Features:41gram 1-2s brushless Toothpick droneNew AIO 4in1 CrazybeeX flight controller CADDX ANT CameraNew 1202.5 brushless motorXT30 connectorRecommend to use 2s 350mah/400mah/450mah/520mah battery（battery not included）Compatible with Insta360 Go Camera You may...

Happymodel 2.4g ExpressLRS ELRS nano series receiver module PP RX/ EP1 RX/ EP2 RX Notes:Since the Official Perfect version of ELRS firmware has not been released yet, currently our PP_RX, EP1/EP2 RX and ES24TX pre-loaded firmware are all beta versions, you can upgrade the...

Happymodel 2.4g ExpressLRS ELRS TX module ES24TX-Lite for T-lite Introduction：Specific Lite 2.4GHz ExpressLRS TX module for Jumper T-lite is coming out now.This Lite TX module is designed by Happymodel and based on the open source- ExpressLRS which is a very popular low latency and...

Introducing the Happymodel Bassline 2s FPV Racer, designed in collaboration with team pilot Nathan Loopz and now available after being conceptualized in 2019. Experience ultimate control and performance with the X12 5-in-1 AIO flight controller featuring built-in 2.4G ELRS V2.0 and OPENVTX. Long-range transmission...

Looking for a high-performance drone that can keep up with your skills and demands? Look no further than the Happymodel Bassline Digital HD 2S Toothpick Drone! Equipped with an HD Digital VTX system and powerful EX1103 KV11000 motors, this drone is built to handle...

Happymodel BeecoreX FR Brushed F4+ESC +VTX+RX+OSD Flight Controller For Inductrix Tiny Whoop E010 E010S - Frsky Receiver The BeecoreX is a ultimate flight controller for Brushed Tinywhoop , it include F4 FC, vtx , ESC, frsky receiver and betaflight OSD. It makes very easy to build a brushed tinywhoop....

Are you ready to upgrade your 65mm/75mm/85mm whoops?YES!! The Happymodel CrazybeeX built-in ESC/VTX/Frsky SPI RX/OSD will handle 1-2S battery!! Note:This product is discontinued. Important: Not compatible with big propeller like 65mm/75mm when use 2s battery . Recommend max size of propeller is 55mm. Flight...

Happymodel CrazyF4 ELRS AIO 5in1 Flight controller built-in 900MHz(915MHz or 868MHz optional) ELRS Receiver Specifications:Flight controllerMCU: STM32F411CEU6 (100MHZ, 512K FLASH)Sensor: MPU-6000(SPI connection)Original whoop size compatiblePower supply: 1S battery input (DC 2.9V-4.35V)Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 readyBuilt-in Betaflight OSD(SPI Control)Built-in 5.8G VTXBuilt-in Serial-based ExpressLRS...

The CrazyF411 ELRS flight controller comes with integrated UART 2.4GHz ExpressLRS receiver and 20A Blheli_s ESC(Bluejay firmware pre-installed) which could support 2-4s. Bigger Mosfet could support high to 20A currents would be better for 2-4S toothpick drone or long range FPV drone. And because...

Happymodel CrossF4 ELRS 1-2S Flight Controller with Onboard UART ExpressLRS 2.4GHz Receiver Specification:Flight controllerFirmware target: CRAZYBEEF4DX4.3.2MCU:STM32F411CEU6 (100MHz, 512K FLASH)Sensor: BMI270(SPI connection)Power supply: 1-2S Lipo Lihv battery input (DC 2.8V~8.7V)Built-in 5A(each) Blheli_S 4in1 ESC Dshot300 readyBuilt-in Betaflight OSD(SPI Control)Built-in UART ExpressLRS 2.4Ghz receiver(Default firmware ExpressLRS v3.0.1)Built-in...

Happymodel Crux3 1S ELRS 3inch toothpick FPV Racer Drone  Note: The Caddx peanut camera is not included, you can buy it HERE   Features:40gram 1s brushless Toothpick droneAIO Flight controller with ELRS Receiver and 5.8G VTX CADDX ANT CameraNew 1202.5 KV11500 brushless motorRecommend to use...

Happymodel Crux35 HD version CRUX35 HD is an ultra-lightweight 3.5Inch FPV Freestyle FPV Racing Drone, the weight of the whole drone is only 87g for the analog version and 108g for the digital HD version. The Crux35 serials drone use Happymodel EX1404 high-efficiency motor...

Happymodel DiamondF4 AIO 5-IN-1 Flight controller built-in VTX ESC OSD Receiver with Frsky/Flysky Receiver For Moblite 6/7 Specification:Flight controller(Frsky SPI RX version) DiamondF4 FR FC Firmware target: CrazybeeF4FR(Flysky SPI RX version)DiamondF4 FS FC Firmware target: CrazybeeF4FSMCU:STM32F411CEU6 (100MHZ, 512K FLASH)Sensor: MPU-6000(SPI connection)Original whoop size compatiblePower supply:...

Note: The Happymodel ELRS X1 AIO 4in1 Flight controller is no longer available. Please order the upgraded X12 ELRS V2.0   The ELRS X1 flight controller comes with integrated SPI 2.4GHz ExpressLRS receiver and 12A Blheli_s ESC which could support 2-4s. Bigger Mosfet could...

The ELRS X2 flight controller comes with integrated SPI 2.4GHz ExpressLRS receiver and 12A Blheli_S ESC which could support 2-4s. Bigger Mosfet could support high to 12A currents would be better for 2-4S toothpick drone or long range FPV drone. And because the 2.4GHz...

Happymodel EX0802 KV19000/KV22000/KV14000 New Brushless Motors for Tinywhoop(Pack of 4)  Happymodel EX's new 0802 whoop special motor, adhering to the consistent style of the Happymodel brushless motor with high quality and high cost performance, using tile-shaped magnets, high-precision CNC housing, high efficiency, good dynamic...

Happymodel EX1102 19000KV 1s Brushless Motor (Pack of 4) Happymodel's new EX1102 KV19000 series motor, the lighter 1102 brushless motor weighs only 2.9g, cool design, with imported NMB double bearings, step shaft double snap springs, more durable. Specifications:Mode: EX1102 KV: 19000Configu-ration: 9N12PStator Diamter: 11mmStator...

Happymodel EX1105 KV5200 Brushless Motors (Pack of 4) Specification:Brand Name: HappymodelModel: EX1105Item Name: 1105 KV5200 3-4S Brushless MotorConfigu-ration: 9N12PStator Diameter: 11mmStator Length: 5mmShaft Diameter: Φ1.5mmMotor Dimension(Dia.*Len): Φ14mm*17mmWeight: 5.7gWire length: 70mm include the connectorPlug interface: JST 1.25mm 3pinFeatures:- New design rotors- High efficiency and smooth-...

Happymodel Moblite6 1S 65mm Ultra light Brushless Whoop FPV Racing Drone Specifications:Brand Name: HappymodelItem Name: Moblite6 1S 65mm ultra light brushless whoopWheelbase: 65mmSize: 80mm*80mm*25mmWeight: 18.5g (without battery)Weight:26g(with Original 1s 300mah Lipo battery ) Features:The lightest 1s 65mm brushless whoopPowerful and efficiencyThe lightest 1s AIO...

Happymodel Moblite7 1S 75mm Ultra-light Brushless Whoop FPV Racing Drone   Specifications:Brand Name: HappymodelItem Name: Moblite7 1S 75mm ultra light brushless whoopWheelbase: 75mmSize: 97mm*97mm*25mmWeight: 19.5g (without battery)Weight:36g(with Original 1s 650mah Lipo battery ) Features:The lightest 1s 75mm brushless whoopPowerful and efficiencyThe lightest 1s AIO...

Specifications:Brand Name: HappymodelModel: Moblite7 WalksnailFrame wheelbase: 75mmWeight: 33.5 gram without batterySize: 98mm*98mm*48mmReceiver option:SPI ELRS 2.4GHzSPI FRSKY 2.4GHzCompatible with 1S Lipo battery or Lihv batteryBattery Plug: PH2.0 Flight controllerSuperbeeF4 Lite ELRS/FRSKYSPI ELRS version Firmware target: CrazybeeF4SX1280SPI FRSKY version Firmware target: CrazybeeF4FRMCU:STM32F411CEU6 (100MHz, 512K FLASH)Sensor: MPU-6000...

The flight controller updated to CrazybeeF4 Lite v3.1 since 17th Feb 2022 ,please check the update log Notice: The flight controller of DSM2/DSMX version Mobula6 has been updated to be CrazybeeX DXS V1.0 after Dec.9th 2020 , it has built-in DSM2/DSMX spi receiver , so...

Happymodel Mobula6 ECO 2024 1S 65mm HDZero Ultra Light Micro FPV Whoop Drone ETA: Around Early April Features:AIO Flight controller with Serial ELRS ReceiverCompatible with HDZERO systemEquipment with the lightest brushless motors-SE0702 only 1.49gramHDZERO NEW ECO VTX and Camera readySmooth and powerfulCompatible for 1S...